QRT
全日通电器（深圳）有限公司

QRT ELECTRICAL APPLIANCE(SHEN ZHEN)LIMTED

Quality is the life customer is God

QRT
QRT

HOTLINE : +86-755-28112701

  • banner
  • banner
  • banner
  • banner
NEWS
Check category
QRT

Address: No.182, Huangdang Road, Dalang Street, Baoan District, Shenzhen City, Guangdong, China
Postal Code: 518109
Tel：+86-755-28112701
　　　+86-755-28112702
Fax：+86-755-28112705

E-Mail：zzq@qrt.com.cn

Homepage
>
news
Introduction

Introduction of electric heating tube

Electric heating tube refers to a tubular electric heating element, mainly composed of iron-chromium-aluminum alloy, nickel-chromium alloy heating wire, stainless steel or copper tube metal tube shell, filled with magnesium oxide powder with good insulation and thermal conductivity, and nozzle It is composed of sealing agent such as silicone rubber for sealing at both ends. Electric heating tubes are classified by medium Electric heating tube for heating water, weak acid and weak alkali liquid Electric heating tube for thawing food oil Electric heating tube for strong acid and alkali heating Electric heating tube for heating in still air Electric heating tube for heating in air at a certain flow rate Aluminum alloy, copper and other components are cast and embedded in them with electric heating tubes Calculation of the calorific value of electric heating tube A voltage regulator can be used to change the heat output by changing the input voltage and current. The calorific value is proportional to the square of the voltage and proportional to the square of the current. When the voltage becomes 1/2, the heat generation becomes 1/4 When the current becomes 1/2 of the original, the heat generation also becomes 1/4 Visual inspection of electric heating tube The most intuitive way to verify the quality of the heating tube is: first wipe the surface of the heating tube, then switch on the AC 220V power supply, dry it in the air, turn off the power after the surface becomes red, and wipe it with a napkin after the heating tube is completely cooled. There should be no black oxidized powder (not reacting with oxygen in the air), indicating that it is a high-quality electric heating tube. The basic requirements are: The surface of the electric heating tube is clean, without obvious scars, no bending, deformation, etc.
2020-08-28
查看全文
Electric

Electric heating tube knowledge

Electric heating tube is a common electric heating element, which mainly appears in metal tube, also called heating tube or heating tube. Its shell tube mainly includes stainless steel tube, copper tube, and iron tube. The electric heating tube mainly includes four parts: metal tube, heating wire, magnesium oxide powder, and port. As a traditional electric heating device, electric heating tube has the characteristics of simple structure, high mechanical strength, high thermal efficiency, safety and reliability, easy installation and long service life. The products are widely used in rubber machinery, plastic machinery, food machinery, spraying equipment, baking equipment , Electroplating equipment, electronic equipment, electrical equipment, air conditioners, wave soldering furnaces, microwave ovens, electric water heaters, coffee pots, ovens, heaters, and shoe machines and other industries. 1. Pipe and temperature design Stainless steel SUS316L: 700° Stainless steel SUS321: 700° Stainless steel SUS304: 650° Cu (nickel plating): 250° AL: 350° Fe (copper plating): 450° 2. The highest surface load of commonly used heating medium (W/cm2) Generally, the watt density of electric heating tube is 5W/cm2 or 6 W/cm2. The watt density of the empty heating tube should not exceed 9 W/cm2, and the watt density of boiling water should not exceed 30 W/cm2. Three, heating wire 1. The heating wire of the high temperature electric heating tube is Ni-Cr wire, with a temperature resistance of 1400oC; 2. The heating wire of the medium and low temperature electric heating tube is Fe-Cr wire, with a temperature resistance of 1500oC. Disadvantages: easy to oxidize and short life. 3. The watt density at the R angle of the electric heating tube is lower than that of the straight part. The temperature difference between the two will be about 20oC during heating, and it will be controlled at about 10oC after oil pressure treatment. 4. The diameter of the heating wire is between 0.12 and 0.6. Four, fill (Mgo) The gap of the electric heating tube is filled and compacted with magnesium oxide powder with good insulation and thermal conductivity 1. Put the cut empty tube on the powder adding machine and add magnesium powder to the empty tube. 2. Remove the powdered tube, pour the magnesium oxide powder 1-2mm away from the tube mouth, and then insert the rubber sheet. 3. The electric heating tube with added powder must be tested for 2000V/0.5MA withstand voltage before shrinking the tube. 4. The shrunken electric heating tube should be tested and marked according to the designed terminal length, and it must be within its tolerance range. 5. Sealing and fasteners According to the customer's needs, inject the required sealing agent into the two nozzles, insert silicone or ceramic beads into the electric heating nozzle, and rotate to make the sealing agent evenly distributed around the nozzle. Electric heating pipe fasteners generally include iron and copper materials, and Teflon wires or rubber sleeves can be used according to customer needs.
2020-08-28
查看全文
October

October 2011 Hong Kong International Electronics Technology and Manufacturing Exhibition

October 2011 Hong Kong International Electronic Technology and Manufacturing Exhibition October 2011 Hong Kong International Electronic Technology and Manufacturing Exhibition October 2011 Hong Kong International Electronic Technology and Manufacturing Exhibition October 2011 Hong Kong International Electronic Technology and Manufacturing Exhibition October 2011 Hong Kong International Electronic Technology and Manufacturing Exhibition October 2011 Hong Kong International Electronic Technology and Manufacturing Exhibition October 2011 Hong Kong International Electronic Technology and Manufacturing Exhibition October 2011 Hong Kong International Electronic Technology and Manufacturing Exhibition October 2011 Hong Kong International Electronic Technology and Manufacturing Exhibition October 2011
2020-08-28
查看全文
Previous page
1

© 2015 Shenzhen Baoan Dalang QRT Electric Factory

Add: No.182, Huangdang Road, Dalang Street, Baoan District, Shenzhen City, Guangdong, China

Code: 518109

Key words:Heating pipe, electric heating tube, heating element, aluminum die casting, die cast aluminum heating element, die cast aluminum body, coffee machine, steam cooker, electric iron soleplate, barbecue stove, electric water heater